Questions about sending and receiving encrypted email
When you send out an unencrypted, digitally signed message or a message with your public key attached (so you can send encrypted messages to them in the future), can't that message be intercepted and...
View ArticleExchange 2010 internal only recieve connectors
I created an internal only receive connector using only the anonymous permission this worked but resolution did not. I found to get resolution I need to enable externally secured this required exchange...
View ArticlePrevent disclaimers from collating at bottom of email chain
Looking to append each reply with disclaimer vs. all at the bottom.Thanks. From: user1 (Mars) Sent: Monday, May 05, 2014 1:20 PMTo: user2 (Earth)Subject: All at the bottom disclaimers ExampleUser1...
View ArticleRedirect messages sent to distribution group
I have a need to set up a hub transport rule as follows:If recipient is a particular distribution groupAnd If subject contains "String A" or "String B"Then Redirect to these specific peopleIt would...
View ArticleCannot enable custom DSN
Hello,I am trying to create a custom DSN to send a NDR alerting the internal sender that his/her mail has been rejected due to profanity. I created a DSN 5.2.9 with the message "Your message appears...
View Articleoutbound emails stuck in queue - 451 error
Hi,We received the below error message in particular domains."451 4.4.0 Primary targeted IP address responded with: "421 4.2.1 Unable to connect." Attempted failover to alternate hosts, or delivery...
View Article2 Edge servers with different HELLO FQDN
I have 2 Edge servers subscribed to 1 site. How can I specify HELLO FQDN for each my edge server, because they have 2 different public IPs and 2 different public DNS names?
View ArticleExchange 2013 SP1 Console powershel access denied and my emails remains in...
hello ,i have exchange 2013 SP 1 , console powershel run in erruer access denied and my emails remains in Draft.i have 2 servers cas (NLB) and 2 server MBX (DAG)any help plz. COMMENTAIRES : Connexion à...
View ArticleRelay Receive Connector - Recipient Limit is not respected
Hi,I have configured a Relay Receive Connector for an application and I set the Recipient limit for it, 50 recipients.Unfortunately this limit is not being respected, the application can send emails to...
View ArticlePublic Folders forwarding to internal address
Hello, we have set forwarding from Public Folder to internal user and selected to forward to both addresses but the mail is only delivered to users mailbox, not to PF, the same is with transport rule,...
View ArticleMail Flow Issue In Exchange Server 2010
Hello,I have an on-premises environment where I have an exchange 2010 hub and edge server. I have 4 domains. All my emails are routed through edge server to the internet. When I send an email from my...
View ArticleExchange 2013 Frontend Receive Connector - cannot telnet port 25
Hello There,I’m going to proceed with migration form exchange 2007 to 2013 but just encounter problem.I can telnet port 25 form new Exchange 2013 server but cannot telnet it form any other computer...
View ArticleError in upgrading from Exchange 2010 SP2 RU6 to Exchange 2010 Sp3.Setup...
Hi We are getting below error on few of CAS servers when we try to upgrade to Exchange 2010 SP3 while uninstalling the IU for SP2"Setup wizard for update rollup6 for Exchange Server 2010 Service Pack 2...
View ArticleMessages going to junk email folder
Hi,We have exchange 2013 deployed and from few days some emails on all users are going to their outlook 2007, 2010 Junk-Email folder.How can i stop same from Exchange 2013 Server side?Best Regards,...
View ArticleExchange 2013 SP1 attachment icon
Hello, our Exchange acts strange when it comes to attachments. The behavior seems to be random. Sometimes in OWA and Outlook the attachment icon is not visible but the attchment is in fact there...
View ArticleExchange Server 2013: Not Sending and Receiving email
Hello, I have a new Exchange Server 2013 install single node and i am having problems sending and receiving email. When testing from https://testconnectivity.microsoft.com/ it fails at the last...
View ArticleRestricting Incoming Mail to deliver during office hours
HelloCan you restrict Exchange (2007) in my case to deliver email to users during certain hours of the day.Currently we have several users asking as they are getting email coming into their phones late...
View Articleoutbound email IP address returns firewall ip not mx record ip
Hi all,We are sending emails fine but some are rejected from some SMTP domains withy the message below:'450 4.7.0 Proxy session setup failed on Frontend with '451 4.4.0 Primary target IP address...
View ArticleTransport rule to forward all incoming and outgoing mail from all users
Hi, I need help to setup a rule that will copy all mail from all people in my organization to an external email account.I have seen rules that apply to only one user, I want a rule that will apply to...
View ArticleExchange Anti-Malware and Trend Micro
Hellow,I am finalizing an Exchange 2013 deployment and I have a question:I have installed Trend Micro as the anti-virus solution for my exchange servers, but this is a file-level protection software, I...
View Article